Model 976LM, 977LM, 976LMC, 940CB
Security+ Wireless Keyless Entry
For use with
any SECURITY+ garage door openers having an orange “learn” button.
Up to 10,000 possible combinations. Password can be easily changes if desired.
be added for visitors or service persons. This temporary password can be limited
to a programmable number of hours or a programmable number of entries.
your password remains constant until you change it, the code between the Keyless
Entry and the receiver changes with each use, randomly accessing over 100
billion new codes.
Opener activates when 4-digit password and Enter button is pressed.
numbers are accidentally pressed, correction can be made immediately. The Enter
button will transmit only the last four digits.
will blink for 15 seconds after the password is transmitted. During that time
the Enter button can be used to stop or reverse the door travel.
THE PERSONAL ENTRY PASSWORD:
that you program your password now, before you install the Keyless Entry. Then
you can test the reception at the mounting location before you proceed further.
MULTI-FUNCTION DOOR CONTROL:
- Enter a four-digit
personal identification number (PIN) of your choice on the keypad. Then press
and hold ENTER.
- While holding the ENTER
button, press and hold the LIGHT button on the Multi-Function Door Control.
- Continue holding the
ENTER AND light BUTTONS WHILE YOU PRESS THE PUSH BAR ON THE Multi-Function
Door Control (all three buttons are held).
- Release buttons when the
motor unit lights blink. It has learned the code. If light bulbs are not
installed, two clicks will be heard.
************* WARNING *************
Moving Door can cause serious injury or death.
DO NOT install transmitter
unless the door operator’s safety reverse works as required by the door
Wall control must be
mounted in sight of door, at least 5 feet above floor and clear of moving door
clear of opening while door is
allow children to play with the
transmitter or door operator.
reverse does not work properly:
Close door then disconnect operator
using the manual release handle.
use transmitter or door operator.
Refer to Door and Door
Operators Owner’s Manuals before attempting any repairs.
can cause serious injury or death.
Power cord must be unplugged
before attaching any wires,
Be sure wire ends do not touch
each other or other terminals.
If you have questions or if you need a manual, contact the
distributor or manufacturer of the operator.
USING THE “LEARN” BUTTON
and release the “learn” button on motor unit. This
can be found where you see the antenna wire hanging from the motor head (you may
have to take the lens cover off). If antenna wire is not hanging from motor head
then you have an external receiver which is a black box approx. 6" x 2" mounted
somewhere in the garage with a antenna wire hanging from it (pop off cover to
find Learn Code Button).
The learn indicator light will glow steadily for 30 seconds.
30 seconds, enter a four-digit personal identification number (PIN) of your
choice on the keypad. Then press and hold the ENTER button.
the button when the motor unit lights blink. It has learned the code. If light
bulbs are not installed, two clicks will be heard.
convenient location for installation. It should be at eye level. Reachable by
the shortest person who will use it, and within sight of the door.
one-piece door, install on exterior front wall to avoid injury as the door
swings up and out.
reception of the Keyless Entry by operating your opener from the selected
location. Change the location if necessary.
battery compartment cover to access the bottom-mounting hole:
Insert a small
Phillips screwdriver into the small hole at the bottom of the cover and gently
pull outward to loosen.
Slide cover down to
keypad at eye level against the selected location. Mark 4-1/4 “ up the
centerline from the bottom and drill a 1/8” pilot hole. Install top mounting
screw, allowing 1/8” to protrude above the surface. Position keypad on screw
head and adjust for snug fit.
open so bottom-mounting hole is visible, use a punch to mark hole. Remove keypad
and drill 1/8” pilot hole. Replace keypad and complete installation with bottom
screw, using care to avoid cracking plastic housing. Do not over tighten.
the battery cover, insert the lip at the top and snap in place.
THE KEYLESS ENTRY BATTERY
battery should produce power for at least one year. Replace when the keypad
illumination becomes dim. Dispose of old batteries properly.
AN EXISTING, KNOWN PIN:
existing PIN is known, one person may change it without using a ladder.
- Press the four buttons
for the present PIN, then press and hold the # button.
The opener light will blink twice. Release the # button.
- Press the new 4-digit
PIN you have chosen, and then press ENTER.
The motor unit lights will blink once when the PIN has been
Test by pressing the new PIN, then press ENTER. The door should
TO SET A
authorize access by visitors or service people with a temporary 4-digit PIN.
After a programmed number of hours or number of accesses, this temporary PIN
expires and will no longer open the door. It can be used to close the door even
after it has expired. To set a temporary PIN:
Press the four buttons for your personal entry PIN
(not the last temporary PIN), then press and hold the *button.
The opener light will blink three times. Release the button.
Press the temporary 4-digit PIN you have chosen,
and then press ENTER.
The opener light will blink four times.
To set the number of hours this
temporary PIN will work, press the number of hours (up to 255), then press *.
- To set the number of
times this temporary PIN will work, press the number of hours (up
To 255), then press #.
light will blink once when the temporary PIN has been learned.
pressing the four buttons for the temporary PIN, then press ENTER. The door
should move. If the temporary PIN was set to a certain number of openings,
remember that the test has used up one opening. To clear the temporary password,
repeat steps 1-3, setting the number of hours or times to 0 in step 3.
temporary password can ONLY be programmed to keypads working on a Chamberlain or
Lift-Master Garage Door Opener. It WILL NOT work on keypads programmed to an
temporary password will continue to CLOSE the door even after the time has
expired. To eliminate this, program a new temporary password into the keypad.